iBeLink™ DM11G ASIC Dash Miner Support Thread
- Thread starter iBeLink_1
- Start date
Hi,
If you are trying to sell something, please create your own thread so the selling/buying discussions don't clog up support discussions. Thank you.
Hi guys just purchased my 2nd used ibelink i already have my 1st all setup but im having trouble setting up my 2nd one my computer is having trouble finding the ip adress to the ibelink and im connected to the same network i need help guys anything you guys can do to help me??
Hi,
To find the IP address of your 2nd iBeLink, you can try using Advanced IP scanner. It will scan your network for attached devices and gives you their IP address. If it does not show up, it could be that the previous owner set a static IP for the miner and you will need to re-flash the firmware.
Hello ! urgently help! G11 does not configure the interface. the interface flew. I already did not pay back Ibekink such a breakdown. help make everyone a worker. look at what a low megakesh and so very often. Instead of 10.000 500- 800 MH. the guys took 4 pieces, and they still work like that. help or change. let's maintain a reputation! write a personal message. thank you.
Attachments
Hi,
Have you modified the firmware? Some of those headings displayed are not the regular displays of the DM11G. Can you please take a screenshot showing what firmware version you are using?
You can try to re-image the TF card to iBeLink DM11G Firmware Version 3.5.25 and see if it resolves the issue. Here is a burning software if you need one.
The low hashrate is most likely due to the high temperatures you are getting (40C) which has lowered the PLL of each hashing blade. If you can lower the temperatures to around 35C, it should get set back to normal.
Have you modified the firmware? Some of those headings displayed are not the regular displays of the DM11G. Can you please take a screenshot showing what firmware version you are using?
You can try to re-image the TF card to iBeLink DM11G Firmware Version 3.5.25 and see if it resolves the issue. Here is a burning software if you need one.
The low hashrate is most likely due to the high temperatures you are getting (40C) which has lowered the PLL of each hashing blade. If you can lower the temperatures to around 35C, it should get set back to normal.
Last edited:
Thank you for your reply. I did not sew a miner. how do I reduce the temperature?) Fans as a reactive noise. Yes, the temperature is 35-40 degrees. but it's sad that at 40 degrees reduces the hashtrajt. with such a roar of fans)) how can you reduce the sensitivity to temperature?
Hi,
The DM11G is an older model and the limitations of the chips at that time limits the temperature to around 40C. The temperature is hard coded into the firmware and is not changeable. To reduce temperatures, you can try using A/C to cool down the room or use fans to push cold air to the miner or pull hot air away.
There is a managed switch DES-1210-52 / ME, to which antminer and ibelink are connected, antminer is visible on the network, and ibelink does not pass, it works only directly with the router or any other unmanaged switch.
ip static
ibelink latest firmware
firmware DES-1210-52 / ME does not help too
ip static
ibelink latest firmware
firmware DES-1210-52 / ME does not help too
Last edited:
Hi,
If you set the Static IP option, is the correct IP address set in the miner and the router? With a managed switch, there may be additional settings that need to be set to allow internet access. The DM11G works best if connected directly to the router or an unmanaged switch.
I know this is many years later but its worth while to reach out to the community. I was recently sent a DM11G unit to test however it does not appear that the unit is connecting to the network.
The turn on sequence looks to be ok... all lights up blue on the outside of the unit after running its test, however it does not seem to connect to the net where I can search for an IP address, so I cannot get to its main page where I can see the state of the unit or its blades.
Im very technical, but im a little out of the loop when it comes to this unit.
What is the timeframe it takes to power on, and be available to connect?
Im wondering if I need to image the SD card on the little mainboard, but I don't want to do anything to brick the unit.
Thanks in advance!
The turn on sequence looks to be ok... all lights up blue on the outside of the unit after running its test, however it does not seem to connect to the net where I can search for an IP address, so I cannot get to its main page where I can see the state of the unit or its blades.
Im very technical, but im a little out of the loop when it comes to this unit.
What is the timeframe it takes to power on, and be available to connect?
Im wondering if I need to image the SD card on the little mainboard, but I don't want to do anything to brick the unit.
Thanks in advance!