• Forum has been upgraded, all links, images, etc are as they were. Please see Official Announcements for more information

iBeLink™ DM22G ASIC Dash Miner Support Thread

Hi,

Since our miners are ASIC (Application Specific Integrated Circuit) machines, no firmware will be able to change the algorithm. Baikal Miner's machines as I understand are FPGA (Field Programmable Gate Array) which means they can use firmware to change the algorithms on their miner.

Do you have the opensource of the CG miner ?
 
I am currently using zpool and has set the difficulty to 92.
unfortunately while monitoring the Ibelink DM22 difficulty is erratic from 48-80..

while my other antminers have a stable 92

what should I input in the password field

currently I use

c=<DASH>,d=92

but on the dm22 it always changing

I want it to be stable at 92
 
Hi,

To add more parameters into the password field, you will need to do that manually in the config file. Here are the steps:

1. Access the miner through file explorer on your computer. You can use the hostname or the IP address.
ad2e00de727e41216cd7d5fdc6c727c2.jpg


2. Open the "share" folder. Then use notepad or text editor and open the file "cgminer.conf.xtc".
19147c162ead5562e647060c32d22e0c.jpg


3. Find the pool and look for the "pass" field. You can now add in the extra parameters as shown in the red box pictured above. Please do not make any other changes in the file as it could cause damage to the miner.

4. Reboot the miner and it will now have all the parameters in the pool settings.
9b043557061261e9675711094b12cc51.jpg
 
Hey guys, I just lost connection to Ibelink miner web interface:

This site can’t be reached
ibelink’s server DNS address could not be found.

any ideas?
 
добрый день, коллеги. Вам пишет Dash-специалист из России. Возникла проблема с оборудованием! Ibelink dm22g выдаёт следующую ошибку: connection to 127.0.0.1: 4029 failed: "connection refused". Ошибка возникает периодически, сбрасываются все настройки на заводские, что очень нехорошо. От чего это может происходить и что сделать, чтобы этого больше не было? Спасибо. Можете ответ продублировать на почту [email protected]/
 
Last edited:
[QUOTE = "dmitriy888, post: 152049, member: 20287"] good afternoon, colleagues. You write Dash-specialist from Russia. There was a problem with the equipment! Ibelink dm22g gives the following error: connection to 127.0.0.1: 4029 failed: "connection refused". The error occurs periodically, all settings are reset to the factory settings, which is very bad. From what it can happen and what to do, so that this will not happen again? Thank you. You can duplicate the answer by e-mail [email protected] / [/ QUOTE]
Hi,

After you have changed your settings, you will need to hit the Save Configurations button at the bottom. This will save so when the miner restarts it will still have your settings.
You can try the Restore button or re-image the sd card with this image file. Burning software and instructions are here. If the error keeps occurring, the sd card could be bad and need to be replaced. You can try first with a card from a working machine to test.
 
thanks . was able to configure it thanks.

unfortunately I am getting more than 150% discards on these pools.

is there anything i can check?
this is always the case with the ff pools
antpool
coinmine
zpool and
multipool.

i dont think my net connection is not the problem since we have a stable 50mbps and never had a problem with it before.
 
thanks . was able to configure it thanks.

unfortunately I am getting more than 150% discards on these pools.

is there anything i can check?
this is always the case with the ff pools
antpool
coinmine
zpool and
multipool.

i dont think my net connection is not the problem since we have a stable 50mbps and never had a problem with it before.
Hi,

It could be the coin switching that is causing the high discards. What firmware version are you currently running and can you enable #xnsub?
 
Hi,

It could be the coin switching that is causing the high discards. What firmware version are you currently running and can you enable #xnsub?


extranonce is already enabled. its just annoying that I have to restore the machines everyweek since after about a week of use , the machines will only has about 9-12ghs after hashing 18-21ghs for the first 2 days of restoring
 
its IB3.6.6 now.

i think the IB3.6.5 version is way better and much more stabler than the latest one
Hi,

If you would like to go back to IB3.6.5, it is still available for download on our website. Here is also a quick link to the firmware.
i am curious about what temperatures your machine is reporting after a week of use.
 
now its high at 39-40.
due to humidity
Hi,

It is possible that the temperatures is causing the PLL to drop lower than 380, which would affect your hash rate. Usually when the temperature gets around 38-40C, it would start to lower your PLL. If you can try to keep your temperatures below that, you should get back to normal hash rates.
 
Hi, please help - I can not do any action - say, when I click on the config button, I throw it onto the login screen. And when I try to make restart, then a window with an html code pops up - apparently the same password input box. Screenshots attached.
 

Attachments

  • main screen.png
    main screen.png
    382.4 KB · Views: 176
Back
Top