2 MasterNodes for 1 wallet?

[Rajak]

Hello

in masternode.conf (for dash qt) i made settings like this

MN900 MN-ServerIP:9999 PrivateKey1 TransactionNumber1 0
MN901 MN-ServerIP:9999 PrivateKey2 TransactionNumber2 0

and dash.conf in remote server (MN server) looks like

#---
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey1
externalip=MN-ServerIP



#----
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey2
externalip=MN-ServerIP

but it doesnt worked. can someone help me?

 

[strophy]

What exactly didn't work? What was your expected behaviour and what actually happened? Did you see an error message?

In general each masternode must have a unique IP address. Are you trying to run two masternodes on one IP address?

 

[Rajak]

Yes i am trying to run 2 masternodes on one IP.. so it is problem?

what if i will add on server another IP address and then will try to activate another masternode with that IP... i am insteresting if would have 2 IPs and 2 masternodes is this configuration correct for it?

 

[TaoOfSatoshi]

Yes i am trying to run 2 masternodes on one IP.. so it is problem?

what if i will add on server another IP address and then will try to activate another masternode with that IP... i am insteresting if would have 2 IPs and 2 masternodes is this configuration correct for it?

Yes, this is the correct configuration. Multiple MNs per IP is not supported.

 

[Rajak]

Thank you i will try to add new IP to my remote serv and then try this configuration.

externalip=MN-ServerIP1
externalip=MN-ServerIP2

it must be like that yes?

 

[Rajak]

Hello again.

I also added IpV4 address to my server,

then i configured my Network settings as it says vultr


/etc/network/interfaces
auto lo
iface lo inet loopback

auto ens3
iface ens3 inet static
address mainIPaddress
netmask XXXX
gateway XXXXX
dns-nameservers XXXXX
post-up ip route add XXXX dev ens3


auto ens3:1
iface ens3:1 inet static
address additionalIPaddress
netmask XXXXX


then i configured dash.conf file on server:

#---
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey1
externalip=MainIP



#----
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey2
externalip=AdditionaIP

and masternode.conf for dash wallet


MN900 MainIP:9999 PrivateKey1 TransactionNumber1 0
MN901 AdditionaIP:9999 PrivateKey2 TransactionNumber2 0



how to know that it worked?

thank you

 

[qwizzie]

Hello again.

I also added IpV4 address to my server,

then i configured my Network settings as it says vultr


/etc/network/interfaces
auto lo
iface lo inet loopback

auto ens3
iface ens3 inet static
address mainIPaddress
netmask XXXX
gateway XXXXX
dns-nameservers XXXXX
post-up ip route add XXXX dev ens3


auto ens3:1
iface ens3:1 inet static
address additionalIPaddress
netmask XXXXX


then i configured dash.conf file on server:

#---
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey1
externalip=MainIP



#----
rpcuser=randomname
rpcpassword=randompassword
rpcallowip=127.0.0.1
#----
listen=1
server=1
daemon=1
maxconnections=24
#--------------------
masternode=1
masternodeprivkey=PrivateKey2
externalip=AdditionaIP

and masternode.conf for dash wallet


MN900 MainIP:9999 PrivateKey1 TransactionNumber1 0
MN901 AdditionaIP:9999 PrivateKey2 TransactionNumber2 0



how to know that it worked?

thank you

You can issue a ./dash-cli masternode list full | grep -e MainIP:9999 and a ./dash-cli masternode list full | grep -e AdditionaIP:9999
if it returns both with "ENABLED" it works.

Edit : dont forget to update Sentinel and issue a start from your cold wallet if you want to implement this.