Search results

Hi, If you've forgotten your password, you will need to reimage the micro sd card to reset everything back to factory default. Here is the DM22 Firmware 3.6.5 and a burning software to use. Afterwards, you can then update the miner to the latest firmware from the configuration page.

Hi, I have heard recently that Nicehash is having issues with ASiC compatibility right now. It could be a temporary issue while they figure it out. After you updated to 3.6.11, did you reboot the miner? Try turning off the miner for 1 minute and then back on. If you are still getting the...

Hi, If you set the Static IP option, is the correct IP address set in the miner and the router? With a managed switch, there may be additional settings that need to be set to allow internet access. The DM11G works best if connected directly to the router or an unmanaged switch.

Hi, This usually means there is an internet connection issue. The miners are not able to connect out to the internet. Please check the router settings to see if they are being blocked and if the IP settings are correct. You can also try re-imaging the firmware onto the tf card. Here is the...

Hi, The DM11G is an older model and the limitations of the chips at that time limits the temperature to around 40C. The temperature is hard coded into the firmware and is not changeable. To reduce temperatures, you can try using A/C to cool down the room or use fans to push cold air to the...

Hi, Try to refresh the page several times, sometimes the display is bugged or there is an issue getting the temperature reading. It should cause no issues with the miner if a few are showing -222 as the system still has temperature readings from other blades.

Hi, Please see the post in the DM11G Support Thread.

Hi, Have you modified the firmware? Some of those headings displayed are not the regular displays of the DM11G. Can you please take a screenshot showing what firmware version you are using? You can try to re-image the TF card to iBeLink DM11G Firmware Version 3.5.25 and see if it resolves the...

Hi, Try these steps to add a new pool. It is best to have the needed information in a text file first as the page will sometimes refresh while you are still entering information 1. Put in the pool url, pool username, and pool password. 2. Hit the "Add Pool" button. This should add your pool to...

Hi, I have messaged you with information.

Hi, I am not exactly sure you can add it up like that, but 1 fan is 90 CFM.

Hi, i can't tell you much about the fan but the CFM of the fan is about 90. Hope that helps.

iBeLink is pleased to announce our new next Generation X11/Dash miner. The iBeLink DM56G is now available at our iBeLink.co website. The shipping deadline is May 31th, 2018. The new iBeLink™ DM56G has the following specifications: Hash Rate: 56 GH/s ±5% Power Consumption: 2100 W ±5% (at the...

This thread is created for iBeLink™ DM56G technical support. We will have technical persons monitoring this thread for various technical issues. Please study the User Guide and FAQ carefully on our website before using this ASIC miner. Resellers, sales, complaints, and discussions of our...

Hi, As long as the miner is operating around 35C or below it should be fine. If the temperature gets too hot, the miner will automatically lower the PLL (speed of the chips) until it is cooler. Then the PLL will be returned to normal. There is also a new firmware version IB3.6.9. This fixes...

Hi, To find the IP address of your 2nd iBeLink, you can try using Advanced IP scanner. It will scan your network for attached devices and gives you their IP address. If it does not show up, it could be that the previous owner set a static IP for the miner and you will need to re-flash the...

Hi, Sure, I can give you steps on how to reflash the micro sd card. I assume you have a DM22G miner. 1. Open the miner and remove the micro SD card from the controller board. 2. Download the DM22G firmware IB3.6.5 and the burning software and instructions. 3. Use the burning software to flash...

Hi, I believe you can not mine with the Dash Core wallet. If you would like to get more information, you can join the Dash Nation Discord at dashchat.org.

Hi, The default username and password is both ibelink. If the password was changed and you don't remember it, you will need to reflash the sd card.

Hi, If you are trying to configure the DM22G miner: Pool URL: address of where you are mining Pool User: dash wallet address or username if you signed up with the pool Pool Password: password for your username if you signed up with the pool or it can be anything