• Forum has been upgraded, all links, images, etc are as they were. Please see Official Announcements for more information

Search results

  1. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi I'm mining on zpool and was wondering if the #snub (extranonce.subscribe) what does this do not quite sure? is it required in my address with cgminer/IB3.5.25 or cgminer/IB3.6.5 or is this already active? zpool indicates not active? but seams to work well but not quite sure what it does. Thanks
  2. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi, I thank you for your support during the loss of my miners over the Christmas holidays, this shows the level of commitment the staff have to help customers. Again thanks for all your help and you all have a wonderful new year. Thanks. Happy Miner :) :)
  3. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi The flash of the new card using 3.6.5 in the 22 does the same thing it does not look like it is at the card level more the PI board? Is there away to get a log from the board? Thanks
  4. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    We tried the latest 3.5.25 and 3.5.21 on the 11's and will be trying the 22 today once I get the new cards it is at 3.6.5 and will be used only for that unit.
  5. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    I have a total of 11 units all with the same problem one is even a 22 I'm getting some more cards today and will try to re flash the 22 unit also keep working on the 11 units. Most weird is one unit was not even plugged in during power failure but we had put the new firmware on the day before...
  6. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi Any feed back from the repair techs on problem? Thanks
  7. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Is there anyway to test the PI board? I can check voltages?
  8. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi Goes through self check then goes solid blue with PI board light blinking blue for around 3 to 5 minutes before restarting. Thanks
  9. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi Yes we used Win32 Disk Imager and a couple of others to see if it makes a difference no luck. It does boot up the start-up test but no access to configuration by us or the system as it reboots all the time. Thanks
  10. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi I would agree, yes we tried new 8 and 16 GB cards format to 3.91 GB also both firmware versions were tried for the DM11G units. Is there any more to the procedure when burning the cards and after installing? Does the system read the card on each boot up or do I need to restore or update?When...
  11. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi Yes it does have both yellow and green on network port also yes the machine goes solid blue before restarting. Thanks
  12. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi, it seams to always go through the full boot sequence then the PI board light never stops blinking then restarts boot sequence what would stop each time no matter what card I use, I will try the newer version of firmware to see if makes a difference, is there anything I should do after...
  13. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hi, I have tried restore no luck did burn a few cards still no luck. The machine seem to go back to DHCP after a rollback. What might be in a router to stop from communication? Thanks
  14. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Hello, Just the same old Connection to 127.0.0.1:4029 failed: 'Connection refused' message thanks
  15. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Anyone on shift today? have had no luck getting miners to work again after power loss please help!! Will keep trying to flash new cards what else could it be?
  16. E

    iBeLink™ DM11G ASIC Dash Miner Support Thread

    Lost all miners on power loss and now they will not go to config screen. Have tried to image TF with no luck all lights work goes through boot up then waits and minute or two then reboots. Will try another card instructions on flash kind of weak on instruction.
Back
Top