Search results

  1. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    Hi everyone, We've managed to get the MN up again. Indeed we needed to put the BLS Priv key in both the MN as client config. That was our mistake. This wasn't clearly mentioned in the wiki page. Thank you all for your assistance!
  2. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    Hi qwizzie, That might just be it, we'll try that. In the wiki it isn't clearly mentioned that the bls private key should also be added to the client's dash.conf file. We'll follow up.
  3. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    Hi Qwizzie, We didn't use brackets (""), and we're pretty sure everything was copied correctly. Prepared everything in notepad window so just copy pasted into the dash debug window. Yeah we're out of clues as well.
  4. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    When executing the last command: protx register_submit ***
  5. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    As clearly mentioned in our post, we've tried using the same keys, we've tried all possible combination and keep hitting that same error.
  6. C

    Attention Dash Masternode Owners: Please register with the Deterministic Masternode List now

    Hi Everyone, We've been struggling to start our masternode with the DIP003 protocol. With the last step as mentioned on this page we're getting the below error: bad-protx-key-not-same (code 16) (code -1) We're using the same address (newly generated) for both the owner and voting address...
  7. C

    Can't detect valid external address - unable to start MN

    Hi Devs, I've given this some thought: I have some concerns as to how dashcore currently checks it's external IP and availability through this address at the moment. This works fine for (master)nodes directly on the internet (say VPS'es), however for nodes behind routers (with NAT) this is an...
  8. C

    Can't detect valid external address - unable to start MN

    Hi Udjin, So I think there are some DNAT issues here to blame, apparently packets aren't recognized by the MN host, probably because the source IP is itself: MN --> Router [DNAT Back to MN] --> MN I've implemented a quick and dirty fix by adding our external IP to the host as a virtual...
  9. C

    Can't detect valid external address - unable to start MN

    Hi UdjinM6, I thought so too, but I've made sure port TCP/9999 forwards on both the internal and external interface. In my firewall I can actually see the count of "internal" connections that have been forwarded back to the node. Again, this worked fine before 0.12.1.
  10. C

    Can't detect valid external address - unable to start MN

    Hi Lynx, It runs every minute through cron, and outputs: "Invalid Masternode Status, cannot continue."
  11. C

    Can't detect valid external address - unable to start MN

    Wallet says successfull, mn says: $ dash-cli masternode status { "vin": "CTxIn(COutPoint(0000000000000000000000000000000000000000000000000000000000000000, 4294967295), coinbase )", "service": "190.1.2.3:9999", "status": "Not capable masternode: Could not connect to 190.1.2.3:9999" }
  12. C

    Can't detect valid external address - unable to start MN

    Here you go: $ dash-cli mnsync status { "AssetID": 999, "AssetName": "MASTERNODE_SYNC_FINISHED", "Attempt": 0, "IsBlockchainSynced": true, "IsMasternodeListSynced": true, "IsWinnersListSynced": true, "IsSynced": true, "IsFailed": false }
  13. C

    Can't detect valid external address - unable to start MN

    Hi All, Over the weekend we've tried it various ways, including with and without the externalip option, also with and without port. The remote wallet (with the 1000 dash) uses the masternode.conf as described in the documentation, and is started with "start masternode alias mn1" (if I remember...
  14. C

    Can't detect valid external address - unable to start MN

    To answer oaxaca: Without the port number, thus for example: externalip=190.1.2.3 I'm going to re-try with the latest release now, I will try to get some relevant debug output.
  15. C

    Can't detect valid external address - unable to start MN

    Yes, followed them step by step.
  16. C

    Can't detect valid external address - unable to start MN

    Dear Community, I've come here to find help with our masternode. Ever since the release of 0.12 we're unable to start our masternode. We've done a complete reinstall and used the previous dash.conf file. However we are unable start the MN. The error we're getting is: Not capable masternode...